Section 2: Laser Hazards (2024)

  • Beam Related Hazards

  • Non-Beam Hazards

The hazards of lasers may be separated into two general categories – beam related hazards to eyes and skin and non-beam hazards, such as electrical and chemical hazards.

Beam Related Hazards

Improperly used laser devices are potentially dangerous. Effects can range from mild skin burns to irreversible injury to the skin and eye. The biological damage caused by lasers is produced through thermal, acoustical and photochemical processes.

Thermal effects are caused by a rise in temperature following absorption of laser energy. The severity of the damage is dependent upon several factors, including exposure duration, wavelength of the beam, energy of the beam, and the area and type of tissue exposed to the beam.

Acoustical effects result from a mechanical shockwave, propogated through tissue, ultimately damaging the tissue. This happens when the laser beam causes localized vaporization of tissue, causing the shockwave analogous to ripples in water from throwing a rock into a pond.

Beam exposure may also cause photochemical effects when photons interact with tissue cells. A change in cell chemistry may result in damage or change to tissue. Photochemical effects depend greatly on wavelength. Table 2 summarizes the probable biological effects of exposure of eyes and skin to different wavelengths.

Photobiological
Spectral domain
Eye
skin

Ultraviolet C

(200 nm - 280 nm)

Photokeratitis

Erythema (sunburn)
Skin Cancer
Accelerated skin aging

Ultraviolet B

(280 nm - 315 nm)

Photokeratitis

Increased pigmentation

Ultraviolet A

(315 nm - 400 nm)

Photochemical cataract

Pigment darkening
Skin burn

Visible

(400 nm - 780 nm)

Photochemical and thermal retinal injury

Pigment darkening
Photosenstive reactions
Skin burn

Infrared A

(780 nm - 1400 nm)

Cataract and retinal burn

Skin burn

Infrared B

(1.4mm - 3.0 mm)

Corneal burn, aqueous flare, cataract

Skin burn

Infrared C

(3.0 mm - 1000 mm)

Corneal burn only

Skin burn

Types of Beam Exposures (top)

Exposure to the laser beam is not limited to direct beam exposure. Particularly for high powered lasers, exposure to beam reflections may be just as damaging as exposure to the primary beam.

Intrabeam exposure means that the eye or skin is exposed directly to all or part of the laser beam. The eye or skin is exposed to the full irradiance or radiant exposure possible.

Specular reflections from mirror surfaces can be nearly as harmful as exposure to the direct beam, particularly if the surface is flat. Curved mirror-like surfaces will widen the beam such that while the exposed eye or skin does not absorb the full impact of the beam, there is a larger area for possible exposure.

A diffuse surface is a surface that will reflect the laser beam in many directions. Mirror-like surfaces that are not completely flat, such as jewelry or metal tools, may cause diffuse reflections of the beam. These reflections do not carry the full power or energy of the primary beam, but may still be harmful, particularly for high powered lasers. Diffuse reflections from Class 4 lasers are capable of initiating fires.

Whether a surface is a diffuse reflector or a specular reflector will depend upon the wavelength of the beam. A surface that would be a diffuse reflector for a visible laser may be a specular reflector for an infrared laser beam.

Eye (top)

The major danger of laser light is hazards from beams entering the eye. The eye is the organ most sensitive to light. Just as a magnifying glass can be used to focus the sun and burn wood, the lens in the human eye focuses the laser beam into a tiny spot than can burn the retina. A laser beam with low divergence entering the eye can be focused down to an area 10 to 20 microns in diameter.

The laws of thermodynamics do not limit the power of lasers. The second law states that the temperature of a surface heated by a beam from a thermal source of radiation cannot exceed the temperature of the source beam. The laser is a non-thermal source and is able to generate temperatures far greater than it's own. A 30 mW laser operating at room temperature is capable of producing enough energy (when focused) to instantly burn through paper.

Per the law of the conservation of energy, the energy density (measure of energy per unit of area) of the laser beam increases as the spot size decreases. This means that the energy of a laser beam can be intensified up to 100,000 times by the focusing action of the eye. If the irradiance entering the eye is 1 mW/cm2, the irradiance at the retina will be 100 W/cm2. Thus, even a low power laser in the milliwatt range can cause a burn if focused directly onto the retina.

NEVER point a laser at someone's eyes no matter how low the power of the laser.

Structure Of The Eye (top)

Damage to the eye is dependent upon the wavelength of the beam. In order to understand the possible health effects, it is important to understand the functions of the major parts of the human eye.

The cornea is the transparent layer of tissue covering the eye. Damage to the outer cornea may be uncomfortable (like a gritty feeling) or painful, but will usually heal quickly. Damage to deeper layers of the cornea may cause permanent injury.

Section 2: Laser Hazards (1)

The lens focuses light to form images onto the retina. Over time, the lens becomes less pliable, making it more difficult to focus on near objects. With age, the lens also becomes cloudy and eventually opacifies. This is known as a cataract. Every lens develops cataract eventually.

The part of the eye that provides the most acute vision is the fovea centralis (also called the macula lutea). This is a relatively small area of the retina (3 to 4%) that provides the most detailed and acute vision as well as color perception. This is why eyes move when you read or when you look as something; the image has to be focused on the fovea for detailed perception. The balance of the retina can perceive light and movement, but not detailed images (peripheral vision).

If a laser burn occurs on the fovea, most fine (reading and working) vision may be lost in an instant. If a laser burn occurs in the peripheral vision it may produce little or no effect on fine vision. Repeated retinal burns can lead to blindness.

Fortunately the eye has a self-defense mechanism -- the blink or aversion response. When a bright light hits the eye, the eye tends to blink or turn away from the light source (aversion) within a quarter of a second. This may defend the eye from damage where lower power lasers are involved, but cannot help where higher power lasers are concerned. With high power lasers, the damage can occur in less time than a quarter of a second.

Symptoms of a laser burn in the eye include a headache shortly after exposure, excessive watering of the eyes, and sudden appearance of floaters in your vision. Floaters are those swirling distortions that occur randomly in normal vision most often after a blink or when eyes have been closed for a couple of seconds. Floaters are caused by dead cell tissues that detach from the retina and choroid and float in the vitreous humor. Ophthalmologists often dismiss minor laser injuries as floaters due to the very difficult task of detecting minor retinal injuries. Minor corneal burns cause a gritty feeling, like sand in the eye.

Several factors determine the degree of injury to the eye from laser light:

  • pupil size - The shrinking of pupil diameter reduces the amount of total energy delivered to the retinal surface. Pupil size ranges from a 2 mm diameter in bright sun to an 8 mm diameter in darkness (night vision).

  • degree of pigmentation - More pigment (melanin) results in more heat absorption.

  • size of retinal image - The larger the size, the greater the damage because temperature equilibrium must be achieved to do damage. The rate of equilibrium formation is determined by the size of the image.

  • pulse duration - The shorter the time (ns versus ms), the greater the chance of injury.

  • pulse repetition rate - The faster the rate, the less chance for heat dissipation and recovery.

  • wavelength - determines where the energy deposits and how much gets through the ocular media.

Eye Absorption Site vs. Wavelength (top)

The wavelength determines where the laser energy is absorbed in the eye.

Section 2: Laser Hazards (2)

Source: Sliney & Wolbarsht, Safety with Lasers and Other Optical Sources, Plenum Press, 1980

Lasers in the visible and near infrared range of the spectrum have the greatest potential for retinal injury, as the cornea and the lens are transparent to those wavelengths and the lens can focus the laser energy onto the retina. The maximum absorption of laser energy onto the retina occurs in the range from 400 - 550 nm. Argon and YAG lasers operate in this range, making them the most hazardous lasers with respect to eye injuries. Wavelengths of less than 550 nm can cause a photochemical injury similar to sunburn. Photochemical effects are cumulative and result from long exposures (over 10 seconds) to diffuse or scattered light. Table 3 summarizes the most likely effects of overexposure to various commonly used lasers.

Section 2: Laser Hazards (3)

Skin (top)

Lasers can harm the skin via photochemical or thermal burns. Depending on the wavelength, the beam may penetrate both the epidermis and the dermis. The epidermis is the outermost living layer of skin. Far and Mid-ultraviolet (the actinic UV) are absorbed by the epidermis. A sunburn (reddening and blistering) may result from short-term exposure to the beam. UV exposure is also associated with an increased risk of developing skin cancer and premature aging (wrinkles, etc) of the skin.

Thermal burns to the skin are rare. They usually require exposure to high energy beams for an extended period of time. Carbon dioxide and other infrared lasers are most commonly associated with thermal burns, since this wavelength range may penetrate deeply into skin tissue. The resulting burn may be first degree (reddening), second degree (blistering) or third degree (charring).

Some individuals are photosensitive or may be taking prescription drugs that induce photo-sensitivity. Particular attention must be given to the effect of these (prescribed) drugs, including some antibiotics and fungicides, on the individual taking the medication and working with or around lasers.

Non-Beam Hazards (top)

In addition to the hazards directly associated with exposure to the beam, ancillary hazards can be produced by compressed gas cylinders, cryogenic and toxic materials, ionizing radiation and electrical shock.

Electrical Hazards (top)

The use of lasers or laser systems can present an electric shock hazard. This may occur from contact with exposed utility power utilization, device control, and power supply conductors operating at potentials of 50 volts or more. These exposures can occur during laser set-up or installation, maintenance and service, where equipment protective covers are often removed to allow access to active components as required for those activities. The effect can range from a minor tingle to serious personal injury or death. Protection against accidental contact with energized conductors by means of a barrier system is the primary methodology to prevent electrical shock.

Additional electrical safety requirements are imposed upon laser devices, systems and those who work with them by the federal Occupational Safety and Health Administration OSHA, the National Electric Code and related state and local regulations. Individuals who repair or maintain lasers may require specialized electric safety-related work practices training. Contact the University Safety Engineer at 258-5294 for an electrical safety inspection and/or required training.

Another particular hazard is that high voltage electrical supplies and capacitors for lasers are often located close to cooling water pumps, lines, filters, etc. In the event of a spill or hose rupture, an extremely dangerous situation may result. During times of high humidity, over-cooling can lead to condensation which can have similar effects. A potentially lethal accident occurred at Princeton University when a graduate student opened a laser to wipe condensation from a tube.

The following are recommendations for preventing electrical shocks for lasers for all classifications:

  • All equipment should be installed in accordance with OSHA and the National Electrical Code.
  • All electrical equipment should be treated as if it were “live”.
  • Working with or near live circuits should be avoided. Whenever possible, unplug the equipment before working on it.
  • A “buddy system” should be used when work on live electrical equipment is necessary, particularly after normal work hours or in isolated areas. Ideally, the person should be knowledgeable of first aid and CPR.
  • Rings and metallic watchbands should not be worn, nor should metallic pens, pencils, or rulers be used while one is working with electrical equipment.
  • Live circuits should be worked on using one hand, when it is possible to do so.
  • When one is working with electrical equipment, only tools with insulated handles should be used.
  • Electrical equipment that upon touch gives the slightest perception of current should be removed from service, tagged and repaired prior to further use.
  • When working with high voltages, consider the floor conductive and grounded unless standing on a suitably insulated dry matting normally used for electrical work.
  • Live electrical equipment should not be worked on when one is standing on a wet floor, or when the hands, feet or body is wet or perspiring.
  • Do not undertake hazardous activities when truly fatigued, emotionally stressed, or under the influence of medication that dulls or slows the mental and reflex processes.
  • Follow lockout/tagout procedures when working with hard-wired equipment.
Section 2: Laser Hazards (2024)

FAQs

Section 2: Laser Hazards? ›

Effects can range from mild skin burns to irreversible injury to the skin and eye. The biological damage caused by lasers is produced through thermal, acoustical and photochemical processes. Thermal effects are caused by a rise in temperature following absorption of laser energy.

What are the hazards of Class 2 lasers? ›

A Class 2 laser is not a skin or materials burn hazard. However, even a Class 2 laser can be a distraction, glare or flashblindness hazard for pilots and drivers. NEVER aim any laser towards an aircraft or vehicle that is in motion.

What happens if you look into a class 2 laser? ›

Laser Class 2 (Class II)

That is why it should only be handled while wearing eye protection glasses. This means that even if unintentional exposure may be safe, Class 2 laser beams can cause eye damage when looked at intentionally, especially when using optical instruments like binoculars or an eye loupe.

Which laser class is the most hazardous? ›

Class 4 is the highest class in terms of laser hazards. If you're within the hazard zone, you're exposed to severe eye and skin injuries. In addition, combustible materials shouldn't be in the laser's surroundings to avoid fire hazards. Diffuse reflections of class 4 lasers are also hazardous.

What are the hazards of laser use? ›

Risk of injury increases when viewed with optical aids. Immediate skin hazard from direct beam and immediate eye hazard when viewed directly. Immediate skin hazard and eye hazard from exposure to either the direct or reflected beam; may also present a fire hazard. Non-Ionizing Radiation: Standards and Regulations.

How quickly can a class 2 laser cause eye damage? ›

Class 2 lasers have an output of up to 1 mW and do not damage the eye when the exposure to the eye does not exceed 250 milliseconds. This is normally the time that it takes to react to a bright source of light and close one's eye (the blink reflex).

What class laser is illegal? ›

Anything exceeding 5 mW is a class 3B laser and it is illegal in the USA to promote such devices as laser pointers! Class 3B lasers are capable of causing eye injuries when exposed to the beam. These lasers are also powerful enough to burn some materials and initiate fires.

Why are blue lasers illegal? ›

Safety concerns have been raised about photo- biological effects from blue light laser pointers (400-500 nm) and they should be avoided. Due to the eye's sensitivity to green light, and also green lasers carry a risk of IR exposure, green laser pointers should not be used.

Can eyes recover from laser damage? ›

In more severe cases, the exposed person may experience sudden vision loss followed by improvement over several weeks. Serious complications may still occur during this time so patients with a confirmed exposure should be closely monitored, Dr. Hacker said.

Is there a class 5 laser? ›

Laser Classes chart

There are four main classes for visible-beam lasers: Class 2, Class 3R, Class 3B and Class 4. The first two are relatively safe for eye exposure; the last two are hazardous. The chart below shows that the eye injury hazard increases as the laser's power increases.

What is the difference between Class 1 and Class 2 lasers? ›

CD-ROM readers and laser printers are class 1 lasers. This class includes high-power lasers within an enclosure that prevents exposure to radiation, and that cannot be opened without shutting down the laser. Class 2: A Class 2 laser is safe because the blink reflex limits the exposure to no more than 0.25 seconds.

Which class of laser can start a fire? ›

Lasers emitting accessible visible radiation with a power output of greater than 5 milliwatts (i.e. Class 3B and 4 levels) have: intense radiation emissions. enough power to pose a fire hazard.

Which of these laser classifications is most likely to cause harm to humans? ›

'Hazardous' lasers

All use of Class 3B and 4 lasers in industry, research and education is specified as 'hazardous' because of the potential to cause damage to eyes including blindness, burns to the skin, and fire.

What are the two body parts most at risk from the dangers of lasers? ›

The human body is vulnerable to the output of certain lasers, and under certain circ*mstances, exposure can result in damage to the eye and skin.

How can you protect yourself from laser hazards? ›

However, these safe practices can help prevent accidental laser eye injuries.
  1. 1 Know the sources of laser radiation. ...
  2. 2 Identify the hazards and assess the risks. ...
  3. 3 Limit exposure to laser radiation. ...
  4. 4 Use appropriate eye protection. ...
  5. 5 Provide training.

Which hazard is the most lethal hazard associated with lasers? ›

The most serious hazard associated with lasers is the electrical hazard from the laser power source. Several fatalities have occurred because of this hazard. Most laser power supplies contain severe electrical hazards. They often contain high voltages and energy storage capacitors and may also include water cooling.

What are the hazards of using a laser level? ›

Even though the beam coming out of a laser level has only a small amount of power, it is concentrated enough to harm your eyes. Anyone using a laser level should follow the below precautions: NEVER stare into a laser beam.

What are the hazards of CO2 lasers? ›

Because infrared wavelengths produce heat, uncontrolled exposure to CO2 laser emissions has the potential to damage the eyes and skin. Special caution is required because CO2 laser wavelengths are not visible to the human eye.

Are two safety hazards when dealing with laser printers choose two? ›

Final answer: Safety hazards when handling laser printers include high voltage, posing a risk of electric shock, and hot components, creating a risk of burns.

What are the hazards of laser marking? ›

The most common injuries associated with laser marking are eye and skin injuries from exposure, but such injuries are still rare. Operators should protect their eyes with durable protective eyewear and wear them any time they operate the machine.

Top Articles
Latest Posts
Article information

Author: Sen. Emmett Berge

Last Updated:

Views: 6055

Rating: 5 / 5 (60 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Sen. Emmett Berge

Birthday: 1993-06-17

Address: 787 Elvis Divide, Port Brice, OH 24507-6802

Phone: +9779049645255

Job: Senior Healthcare Specialist

Hobby: Cycling, Model building, Kitesurfing, Origami, Lapidary, Dance, Basketball

Introduction: My name is Sen. Emmett Berge, I am a funny, vast, charming, courageous, enthusiastic, jolly, famous person who loves writing and wants to share my knowledge and understanding with you.